Search results

The purpose of this paper is to quantify the environmental footprint and cost and thus compare different manufacturing scenarios associated with the production of aeronautical structural components.

A representative helicopter canopy, i.e., canopy of the EUROCOPTER EC Twin Star helicopter described in Pantelakis et al. (2009), has been considered for the carbon footprint (life cycle energy and climate change impact analysis) along with the life cycle costing analysis. Four scenarios – combinations of different manufacturing technologies (autoclave and resin transfer molding (RTM)) and end-of-life treatment scenarios (mechanical recycling and pyrolysis) are considered.

Using the models developed the expected environmental and cost benefits by involving the RTM technique have been quantified. The environmental impact was expressed in terms of energy consumption and of Global Warming Potential-100. From an environmental standpoint, processing the canopy using the RTM technique leads to decreased energy demands as compared to autoclaving because of the shorter curing cycles exhibited from this technique and thus the less time needed. As far as the financial viability of both processing scenarios is concerned, the more steps needed for preparing the mold and the need for auxiliary materials increase the material and the labor cost of autoclaving as compared to RTM.

At the early design stages in aeronautics, a number of disciplines (environmental, financial and mechanical) should be taken into account in order to evaluate alternative scenarios (material, manufacturing, recycling, etc.). In this paper a methodology is developed toward this direction, quantifying the environmental and financial viability of different manufacturing scenarios associated with the production of aeronautical structures.

The purpose of this paper is the development of a multiscale model which simulates the effect of the dispersion, the waviness, the interphase geometry as well as the agglomerations of multi-walled carbon nanotubes (MWCNTs) on the Young’s modulus of a polymer filled with 0.4 Vol.% MWCNTs.

For the determination of the homogenized elastic properties of the hybrid material representative unit cells (RUCs) have been used. The predicted homogenized elastic properties were used for the prediction of the Young’s modulus of the filled material by simulating a finite element (FE) model of a tensile specimen. Moreover, the model has been validated by comparing the predicted values of the numerical analysis with experimental tensile results.

As the MWCNT agglomerates increase, the results showed a remarkable decrease of the Young’s modulus regarding the polymer filled with aligned MWCNTs while only slight differences on the Young’s modulus have been found in the case of randomly oriented MWCNTs. This might be attributed to the low concentration of the MWCNTs (0.4 Vol.%) into the polymer. For low MWCNTs concentrations, the interphase seems to have negligible effect on the Young’s modulus. Furthermore, as the MWCNTs waviness increases, a remarkable decrease of the Young’s modulus of the polymer filled with aligned MWCNTs is observed. In the case that MWCNTs are randomly dispersed into the polymer, both numerical and experimental results have been found to be consistent regarding the Young’s modulus.

The methodology used can be adopted by any system containing nanofillers.

Although several studies on the effect of the MWCNTs distribution on the Young’s modulus have been conducted, limited results exist by using a more realistic RUC including a periodic geometry of more than 20 MWCNTs with random orientation and a more realistic waviness of MWCNTs with aspect ratio exceeding 150.

Over the last decades, self-healing materials based on polymers are attracting increasing interest due to their potential for detecting and “autonomically” healing damage. The use of embedded self-healing microcapsules represents one of the most popular self-healing concepts. Yet, extensive investigations are still needed to convince on the efficiency of the above concept. The paper aims to discuss these issues.

In the present work, the effect of embedded self-healing microcapsules on the ILSS behavior of carbon fiber reinforced composite materials has been studied. Moreover, the self-healing efficiency has been assessed. The results of the mechanical tests were discussed supported by scanning electron microscope (SEM) as well as by Attenuated Total Reflection–Fourier-transform infrared spectroscopy (ATR–FTIR) analyses.

The results indicate a general trend of a degraded mechanical behavior of the enhanced materials, as the microcapsules exhibit a non-uniform dispersion and form agglomerations which act as internal defects. A remarkable value of the self-healing efficiency has been found for materials with limited damage, e.g. matrix micro-cracks. However, for significant damage, in terms of large matrix cracks and delaminations as well as fiber breakages, the self-healing efficiency is limited.

The results obtained by SEM analysis as well as by ATR–FTIR spectroscopy constitute a strong indication that the self-healing mechanism has been activated. However, further investigation should be conducted in order to provide definite evidence.